English Tregaskiss a compilé une liste de questions fréquemment posées sur les nouveaux pistolets MIG robotiques à refroidissement par air Tregaskiss CA3 et Tregaskiss TA3 et comment convertir les pistolets MIG robotiques à refroidissement par air des séries TOUGH GUN G1 et / ou G2 en ces pistolets des modèles : Pourquoi ajoutez-vous les pistolets […]
read more...Frequently Asked Questions About the New TOUGH GUN CA3 and TA3 MIG Guns and How To Convert From TOUGH GUN G1 and G2 Series Français Tregaskiss has compiled a list of frequently asked questions about the new TOUGH GUN® CA3 and TOUGH GUN TA3 robotic air-cooled MIG guns and how to convert from the TOUGH […]
read more...Centerfire™ Diffuser Part NumberLiner Trim LengthD-19/16″14.3 mmD-1T13/16″ 20.6 mmD-1T513/16″20.6 mmDS-19/16″14.3 mm DS-1T5/8″ 15.9 mm DW-1 1/4″ 6.4 mmQuik Tip™ Diffuser Part Number Liner Trim Length D1145/8″15.9 mmD114Q 9/16″14.3 mmD1183/4″19.1 mmD118Q 3/4″19.1 mm D118QLL1 5/16″33.3 mm D1FQ 7/8″22.2 mm D2187/8″2.2 mmTOUGH LOCK® Retaining Head Part Number Liner Trim Length ALL3/4″9.1 mm
read more...Frequently Asked Questions About Dual Taper Technology on TOUGH LOCK Retaining Heads Tregaskiss has compiled a list of frequently asked questions about dual taper technology on TOUGH LOCK® retaining heads: Are the TOUGH LOCK retaining heads backwards compatible with older MIG guns?Will TOUGH LOCK retaining heads with dual taper technology cost more?How can I tell the […]
read more...Frequently Asked Questions About the QUICK LOAD® Liner System Tregaskiss has compiled a list of frequently asked questions about the two-piece front-loading QUICK LOAD® liner system: How is the QUICK LOAD® liner retainer installed? How does the QUICK LOAD® liner stay in place? Why is the liner replacement so much faster with the QUICK LOAD® […]
read more...Effective June 27, 2005 In 2005, Q-Gun™ MIG Guns began shipping with upgraded back end assemblies. It is important to know which back end assembly your Q-Gun MIG Gun has when choosing replacement parts. Use the drawings below to determine which back end you have. Old Back End Assembly The rigid strain relief of the […]
read more...ProblemPossible CausePossible SolutionElectrode does not feed or erratic wire feeding.1. Feeder relay / malfunction.Consult feeder manufacturer.2. Feeder relay / malfunction.a. Test & connect spare control lead.b. Install new cable. 3. Poor adaptor connection.Test & replace leads and/or contact pins. 4. Worn or broken switch.Replace switch. 5. Improper drive roll size.Replace with proper size. 6. Drive roll tension misadjusted.Adjust tension at […]
read more...Frequently Asked Questions About Converting Your Keyed or Quick-Change Robotic Water-Cooled MIG Gun to the 600 amp Robotic Water-Cooled Model Tregaskiss has compiled a list of frequently asked questions about converting from the keyed or quick-change robotic water-cooled MIG gun to the 600 amp robotic water-cooled model: I think the 600 amp product will create accessibility […]
read more...Frequently Asked Questions About Upgrading Your Robotic MIG Gun with TOUGH GUN I.C.E. Technology Tregaskiss has compiled a list of frequently asked questions about upgrading your existing TOUGH GUN® robotic air-cooled MIG gun to a model equipped with TOUGH GUN I.C.E.® technology: I think TOUGH GUN I.C.E. components will create accessibility problems. What are my […]
read more...NozzlesContact TipsRetaining HeadsGas DiffusersLinersNecksGun CablesReamers Recommended Operating TipsDownload a copy of the recommended operating tips in PDF format Nozzles: If anti-spatter is used, do not use excessive spray times as this will saturate the nozzle insulator and will degrade insulating material. Learn more about TOUGH GARD® anti-spatter liquid from Tregaskiss.Nozzle should be cleaned as often […]
read more...